|
|
External camera housings for body cameras with 12/24 or 240 Volt Heaters |
To Our Camera Housing and Brackets Page |
Cable managed external camera housing with 12v DC-24v AC heater and bracket External high quality fully cable managed die cast aluminium camera housing with heater, powder coated with side opening lid for easy access, IP66 rating. Supplied complete with cable-managed bracket, dual voltage 12v DC @ 600mA or 24v AC 400mA heater. 405L x 130W x 150H (excluding bracket). PSU sold separately Cable managed external camera housing with 240v AC heater and bracket External high quality fully cable managed die cast aluminium camera housing with heater, powder coated with side opening lid for easy access, IP66 rating. Supplied complete with cable-managed bracket, 240v AC heater. 405L x 130W x 150H (excluding bracket). |
12/24 Volt £64.99 |
240 Volt £64.99 |
External camera housing with built in IR Lighting and Dual Glass Technology |
Large external housing with bracket & IR LEDS with dual glass technology 24v External full sized high quality housing with heater and fan, a fully cable managed bracket is included. The housing is fitted with 11 Ultra high intensity IR LEDs that allow a camera to be used in total darkness up to a range of 80 metres. The housing is designed to accept most standard body cameras and lens combinations .The housing incorporates a dual glass technology that completely eliminates IR LED reflection in to the lens at night. The housing is IP66 rated, 24V AC power supply required. This housing also provides a regulated 12 Volt supply for cameras derived from the housings 24 Volt AC supply and incorporates a built in "Hum Bug" suppression device. A very high quality housing which removes the need for separate IR Lighting while still providing the flexibility of interchangebale camera and lens types. |
Housing with IR Lighting £185.00 |
Internal camera brackets for use with Body or Finger Cameras |
£15.00 |
£5.00 |
£5.00 |
£5.00 |
515/6/7 External camera housings For use with addional mounting nuckle. 12 - 24 or 240 Volt Heaters |
Housing £89.99 |
Nuckle £23.99 |
506 type External camera housings For use with addional mounting nuckle. 12 - 24 or 240 Volt Heaters As above picture but no washer or wiper facility can be added. |
Housing £85.00 |
Nuckle £23.99 |
Camsecure CCTV |
CCTV Equipment Software and Systems |
Low Cost Internal Camera brackets. A range of low cost internal camera brackets suitable for small to medium size finger and body cameras using a standard CCTV mount. Can be used with all Camsecure cameras. |
Standard Metal Bracket |
Standard Mini Bracket |
Medium Bracket, Plastic with Metal Fixing Screw |
Pole Mounting Bracket for our Camera Housings |
This camera housing can also be used with our pole mount clamp and bracket to allow mounting on the side of a pole, mast or lamp post etc. |
Cable managed bracket and easy fixing to wall or poles (with additional fixing kit) make this housing very popular. |
Camera housing for use with separate adjustable mounting nuckle or brackets as required. The type 515, 516, 517 range of environmental camera housings are designed to accommodate a wide range of camera / lens combinations and to provide protection to BS.EN 60529 Level IP 65 (no water ingress). Insulated camera platforms with longitudinal adjustment are supplied as standard, plus window heater, thermostat, three cable glands and full sunshield. Self parking wipers, 5 and 25 Litre washers are available and can be retro-fitted. The housings are constructed from aluminium alloy, powder coated and stoved with stainless steel fittings. Deep base versions are offered to allow telemetry receivers, relay interface units or cable termination trays to be fitted under the camera. By use of a separate adjustable nuckle mount these housings can be mounted on top of flat surfaces, wall parapits, top of columns and poles etc. and still benefit from full angular adjustment. |
The type 506 housing is specifically designed to accommodate a range of C.C.D. cameras. The enclosure incorporates a removable top cover for camera access, similar to our type 515 housing. Units are constructed from zintec sheet, powder coated and stoved. The standard specification includes a heater, two cable glands, adjustable camera platform and stainless steel fittings throughout. Environmental protection is to IP65 at BS.EN 60529. |
Washer and Wiper are optional on this model. |
Nuckle can be used in combination with other Camsecure brackets and housings for unusal installation requirements. |
Nuckle can be used in combination with other Camsecure brackets and housings for unusal installation requirements. |
UNSURE of what housing and bracket combination you need? Cant see what you are looking for? Please Contact Us |
Please state voltage on order |
Please state voltage on order |
Order by Noon for delivery next working day |